The Foundation of Plumbing Skills When Installing a Bathtub

Call Today


What're your insights and beliefs on Installing A Bathtub?


Installing A Bathtub
Mounting a bath tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately hard task. If the old bathtub is easily accessible, the job can move rapidly; if you need to open up a wall to eliminate the old tub and place the brand-new bathtub, the job is a lot harder. In either instance, the task is within a home handyman's abilities, although you will certainly require an assistant to move out the old tub and also set in the brand-new one. Ensure you have qualified yourself for the work and also are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed task, it is far better to take into consideration employing one prior to you start. Opportunities are you may need a professional plumber to make tube links.
This article will help you set up a new bathtub in your washroom if you have actually currently purchased a new tub and also don't need to alter the arrangement of your previous supply of water pipelines.
Your devices as well as material checklist need to make up the following:


  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  •  

Getting ready for the Setup


First of all, the sustaining structure supplied with the bathroom needs to be fitted (if needed) according to the maker's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets system to prevent strain on the tub.
Fit the adaptable faucet connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its last position.



Removing Old Touches


If you require to replace old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, activate the taps to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted access that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.



Installing the Tub


Making use of both wooden boards under its feet, put the bathtub in the required position. The wooden boards are helpful in evenly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the bathtub until the spirit level reviews level.
To mount faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the water system and inspect all joints as well as brand-new pipework for leakages and tighten them if necessary. Load the bath tub as well as likewise examine the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, repair the bath paneling as explained in the supplier's instruction manual. Tiling and securing around the tub ought to wait till the bathtub has been used at least once as this will certainly resolve it right into its last setting.



Fitting New Taps


If the tails of the brand-new faucets are plastic, after that you will require a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin making sure that the washing machines are in place in between the tap and also the sink. Secure the tap in position with the manufacturer offered backnut. As soon as the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The previous type needs to be attached to the faucet ends initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been attached.



Tiling Around the Bath tub


In the area where the bath fulfills the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to break an inflexible seal, causing the water to penetrate the wall in between the bath and also the tiling, bring about complications with moisture and feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to permit the motion experienced when the bathtub remains in usage. The sealant can break fairly early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also quickly offered on the market. It is a good idea to fit the tiles making use of waterproof or waterproof adhesive and grout.


How to Install or Replace a Bathtub


Find Your Dimensions


The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


Disconnect the Water Supply and Drain Assembly


Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


Cut Out the Old Tub


After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


Install the New Tub


Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


Secure the Tub


After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround


As a fervent reader about How to Install a Bathtub, I thought sharing that excerpt was essential. Enjoyed our blog posting? Please share it. Help another person check it out. I love reading our article about Tools You Need to Install a New Bathtub .


Hot water issues? Connect now.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “The Foundation of Plumbing Skills When Installing a Bathtub”

Leave a Reply

Gravatar